This article covers using KICKR Wi-Fi (KICKR v6 and BIKE v2) and Direct Connect (KICKR v5+, KICKR BIKE 2, and ROLLR) features with a Windows PC or Mac.
Wi-Fi Connectivity (KICKR v6 and BIKE v2)
- What is it? a 2.4 GHz Wi-Fi connection (802.11b/g/n, 20 and 40 MHz channel widths, channels 1-11) between trainer and controlling device
- Why is it valuable? Wi-Fi connectivity offers a more robust connection solution for training in your home. Wi-Fi offers lower latency and higher throughput, expanding the capabilities of what our trainer can do.
- How does it work? Through the Wahoo app or SYSTM Device Management, you can connect your trainer to your network. Once set up on a given Wi-Fi network , a KICKR reconnects automatically. See Directions below.
- What apps are compatible?
- Fulgaz - All platforms
- TrainerRoad - All platforms
- Wahoo RGT - All platforms
- Wahoo SYSTM - Windows and MacOS platforms
- Zwift - All platforms
- A 2.4 GHz Wi-Fi connection
- A KICKR v6 or KICKR BIKE v2
- Once the KICKR v6 or BIKE v2 is paired to the Wahoo App, select Settings > Sensors > KICKR (or BIKE/ROLLR).
- Under Wi-Fi, tap 'Select Wi-Fi Network' and select your desired Wi-Fi network from the 'Available Networks'.
- Enter the Wi-Fi network password and tap 'Connect'.
- Once connected, the Network page will appear confirming that the trainer will now be discoverable by supported applications on that same network and provide the trainer's IP and Mac address.
Direct Connect (KICKR v5+, KICKR BIKE v2, and ROLLR)
- A Direct Connect Adapter
Any KICKR v6, BIKE v2, or ROLLR, or a KICKR v5 on Firmware 4.1.1 or newer
- Windows 10 version 19041 20H1 or newer (also supported on Windows 11) OR a Mac
- Bluetooth® enabled on your selected device
Once the Direct Connect adapter is plugged into the KICKR v5+, KICKR BIKE 2, or ROLLR, simply plug one end of an Ethernet cable into the adapter and the other end directly into your PC, router, or Wi-Fi access point depending on your preferred setup.
Connecting Directly to a Windows PC/Mac
Direct Connect and Windows (firewall):
If you are connecting the Direct Connect Adapter directly to your Windows PC, be sure to allow the connection when prompted (typically when opening your selected app). The current working connection type is automatically checked when the prompt appears, but can be edited, if needed, via Control Panel > Windows Defender Firewall > windowsbtle.exe
Once the connection is allowed, the trainer should appear when searching for trainers in your selected app similarly to how it would on a wireless connection.
Direct Connect and Mac:
If you are connecting your trainer to a Mac, the process is as easy as plug and play: simply connect the adapter to your trainer, then connect the Ethernet cable to your Mac and start your desired app to find your trainer listed.
Connecting through a Router or other Network
Simply plug your direct connect adapter into your KICKR and connect the Ethernet cable to your router and it will be found on your PC within your selected app, similarly to how it would be found wirelessly.
Note: The KICKR Direct Connect Adapter is typically assigned an IP address automatically via DHCP. However, it's important to note that the adapter should be on the same subnet as the PC being used (example: if your PC has the address 192.168.0.100, the Direct Connect Adapter should be set to 192.168.0.xxx in order to be recognized on the PC). Most users should not have an issue with this, but there may be cases when running range extenders (or multiple routers) where the range extender is functioning in router mode instead of access point mode on a different subnet.
Other Important Notes
Direct Connect and 3rd Party Firewalls:
3rd party firewalls may block traffic to the adapter including, Norton, McAfee, and Avast. Be sure to disable your 3rd party firewall or allow traffic on port 36866. Follow the instructions for your firewall to allow traffic on this port for the adapter to work properly.
Direct Connect and Bluetooth:
Direct Connect requires Bluetooth® to function and uses the Bluetooth® protocol over TCP/IP. Your PC/MAC must have Bluetooth® drivers and must be enabled in the OS and App. Most computers in the past 7 years should have Bluetooth® by default, but a Bluetooth® adapter may be required if not.
Direct Connect and Multiperipheral:
The Direct Connect Adapter is a 1:1 connection. It will only work in 1 app at a time. Always be sure to close any previously connected apps to ensure visibility with new apps. Note that the default Bluetooth® connection will remain available for other apps to use.